65/66 mustang bucket fit in 72 f100

kevins72 · Post by **kevins72** » Fri Mar 21, 2014 1:01 pm

Hello, does anyone know if 65/66 mustang bucket seats will fit in some of the stock holes and look good and the right height in a 72 f100 ranger. Thanks for your time and input. Kevin

sargentrs · Post by **sargentrs** » Fri Mar 21, 2014 4:37 pm

You will have to make/buy the bucket seat mounting brackets. Here's a link to a discussion with some info on where to get brackets. http://www.fordification.com/forum/view ... &sk=t&sd=a or you could do like I did and make your own seat mounting frame. http://www.fordification.com/forum/view ... =6&t=66309

kevins72 · Post by **kevins72** » Sat Mar 22, 2014 9:14 am

Thank you for the info, seems like some work, but worth it, because it looks great, thanks Kevin.

Craigerf100 · Post by **Craigerf100** » Sat Mar 22, 2014 4:03 pm

Yes yes it is

Craigerf100 · Post by **Craigerf100** » Mon Mar 24, 2014 5:11 am

Woops forgot to post the pic with it

kevins72 · Post by **kevins72** » Mon Mar 24, 2014 5:25 am

That looks nice, I really like the all black. I'm going to start looking for pair more locally so it will help with the shipping cost, that will pay for the brackets. Thank you. Kevin

Craigerf100 · Post by **Craigerf100** » Mon Mar 24, 2014 8:44 am

Did u contact bill w about the brackets?

kevins72 · Post by **kevins72** » Mon Mar 24, 2014 9:36 am

No not yet, thought I'd find some seats first, but I do have the link for him, I will contact him just to see if he's got some. Thanks Kevin.

cole71 · Post by **cole71** » Thu Mar 27, 2014 3:06 pm

Does any new holes need to be drilled for the brackets?

Craigerf100 · Post by **Craigerf100** » Thu Mar 27, 2014 4:44 pm

Yes.
I want to say they are marked on your floor from factory. But I don't know that for sure because the trucks PO sprayed some bed dyno liner type stuff on the floor. It's easy though to find n mark the holes to drill.

Tpdaniels · Post by **Tpdaniels** » Fri Mar 28, 2014 8:42 pm

The outside holes in the floor for the bench seat line up perfect for the outside brackets for the bucket seats, There are no holes for the inside brackets but all you have to do is mount them to the outside ones the mark and drill the inside bracket holes.

chicof100 · Post by **chicof100** » Fri Mar 28, 2014 9:25 pm

Along the lines of Bucket seats. If you need the trim pieces that go just below the rear window let me know.
These were installed to cover the top edge of the carpet. There were also two angles that were installed to the B-pilar's
to attach the lower part of the carpet. This way your gas tank was covered so you still had a nice look.
These trim pieces will also work if you have removed your gas tank and you want to break up the back wall, paint and carpet
or two tone paint.

Craigerf100 · Post by **Craigerf100** » Fri Mar 28, 2014 11:42 pm

I'm surprised U still have those.

chicof100 · Post by **chicof100** » Sat Mar 29, 2014 7:09 am

Craigerf100 wrote:I'm surprised U still have those.

I've been picking them up when I find them. I've sold three sets, I think I have three or four sets left.

kevins72 · Post by **kevins72** » Sun Mar 30, 2014 6:54 am

I think I would buy a set, if you would sell one? PM me with info and we'll go from there. Thank you, kevin.

The FORDification.com Forums

65/66 mustang bucket fit in 72 f100

65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100

Re: 65/66 mustang bucket fit in 72 f100